Hold the hose.
A ratchet clamp for 16–18 mm LDPE hose. Check the hose size before selecting the clamp.
LDPE Ratchet Clamp for 16mm to 18mm Hoses
$0.25 each
View clamp
Irrigation parts.
For hands-on gardens.
Fittings, tubing and valves for everyday garden irrigation.
Shop irrigationControl
the flow
What does your
connection need to do?
A straight run, a corner and a branch call for different shapes. Compare these three real options from the 1/4″ micro-fitting range.
A straight connection.
A coupling continues the line in the same direction. This 1/4″ micro fitting has two barbed ends.
Coupling · 1/4″ · SKU FC250
$0.09 each
View coupling
Same shape. A different family.
The 1/4″ micro coupling above and this 3/4″ PVC insert coupling both join a straight run. Their names, sizes and connection families are different. Check the whole product specification before choosing, rather than matching the silhouette.
3/4″ PVC insert coupling · $1.05 each
Explore PVC couplings, tees & elbows“1/2 inch” is only
part of the story.
Read the connection type and the measurement that follows it. These adapters make the difference visible in the name.
- ID
- Inside diameter: the opening inside the tubing.
- OD
- Outside diameter: the measurement across its outer walls.
One shared photo.
Three specific listings.
Two of these start with a 1/2″ slip connection, but list different tubing ODs. The 3/4″ slip model lists a different OD again. A photo cannot stand in for those measurements.
1/2″ slip × 0.620″ OD tubingSKU FCA620$0.23 each 
1/2″ slip × 0.700″ OD tubingSKU FCA700$0.23 each 3/4″ slip × 0.940″ OD tubingSKU FCA900$0.41 each
1/2″ slip × 0.700″ OD tubingSKU FCA700$0.23 each 3/4″ slip × 0.940″ OD tubingSKU FCA900$0.41 each Compare the tubing measurement named in the listing. Nominal inch labels, millimetre sizes, ID and OD are not interchangeable labels.
Plan the line
around your plants.
Planter boxes, containers and smaller garden areas bring the route into focus. Think about the length of the run and where the listed emitter spacing will fall before choosing the line.
This coil puts four useful details together:
- Coil length
- 100 feet
- Emitter spacing
- 6 inches
- Listed flow
- 1/2 GPH
- Tube dimensions
- 0.170″ × 0.250″
The coil, fittings and control parts are separate products. Confirm the connections for your setup before ordering.
$16.21 per 100′ coil
View the dripperlineControl and filtration.
Different jobs.
The Green Back Valve is an on/off part for low-pressure irrigation. A filter/regulator is a separate choice with its own connection, flow range and pressure specification.
Pressure Regulating Filter
- Connection
- 1″ MIPT
- This model
- 45 psi · 0.2–10 gpm
- Screen
- 200-mesh stainless steel
Check your system requirements and the flow direction marked on the housing. This model’s figures are not a rating for every part in your line.
$30.40 each · SKU FPRF100
View the filter / regulatorNeed an on/off valve instead? Green Back Valve, 1/2″ · $2.49 each
The last little parts
have different jobs, too.
Holding a hose, closing its end and sealing an emitter hole are separate tasks. Pick the part for the job, then confirm its listed size and sales unit.
Close the end.
A figure-eight fitting closes the end of low-pressure poly tubing. This listing offers 1/2″ and 3/4″ options.
Figure 8 End Plug
From $0.21 each
View end plug
Seal an emitter hole.
Dual plugs have 1/8″ and 1/4″ ends. The sales unit is a rack of 10 plugs; the loose plug in the photo is an illustration, not an extra item.
Dual Goof Plug (10/RACK)
$0.40 per rack of 10
View goof plugsA little attention
to every connection.
A coupling, a tee, an end plug. The useful details are in the connections, dimensions and sales units. DripLattice brings those parts into one place so you can compare them before you choose.
Start with the job on your workbench. Follow it through to the exact product and option you need.
About DripLatticeA question about your parts?
Tell us the product, size and connection you are looking at.